SCB13型环氧树脂浇注干式变压器【价格批发公司】-hjc878黄金城官网

SCB13型环氧树脂浇注干式变压器

所属分类：干式变压器
点击次数：
发布日期：2019/02/26
规格：
类型：
在线询价

详细介绍

产品概述 Overview

相比较SCB12型环氧树脂浇注三相干式变压器，SCB13型干式变压器是升级后的下一代产品，其空载损耗相比SCB12型降低5%，节能效果更显著，同时具有安全，阻燃防火，无污染，可直接安装在负荷中心。免维护、安装简便。防潮性能好，停运后不经预干燥即可投入运行。损耗低，局部放电量低、噪音小、强迫风冷条件下可以120% 额定负载运行。自己备有完善的温度保护控制系统，为变压器安全运行提供可靠保障。该产品的可靠性指标已经达到国内先进水平。

Compared with SCB12 epoxy resin cast three-phase dry-type transformer, SCB13 dry-type transformer is the upgraded next-generation product, its no-load loss is reduced by 5% compared with SCB12, the energy-saving effect is more significant, and it is safe, fire-retardant and fireproof. It is non-polluting and can be installed directly in the load center. Maintenance free and easy to install. It has good moisture-proof performance and can be put into operation without pre-drying after shutdown. Low loss, low partial discharge, low noise, and 120% rated load operation under forced air cooling. We have a complete temperature protection control system to provide reliable protection for the safe operation of the transformer. The reliability index of this product has reached the domestic advanced level.

产品展示 Display

三相干式变压器

型号含义 Meaning

产品特点 Characteristics

1、线圈采用铜导线缠绕或箔绕，以玻璃纤维增强，环氧树脂不加填料真空干燥脱气脱湿整体浇注，机械强度高，抗短路，耐冲击能力强。
2、高压绕组首末端及中间分接抽头采用铜嵌件预埋结构，钢性好，便于调档，美观整齐。
3、铁芯采用优质晶粒取向冷轧硅钢片叠制，45度全斜多阶梯接缝。表面用树脂绝缘涂层覆盖，耐潮湿，防锈，降噪。
4、铁芯、夹件和线圈之间采用弹性件夹紧，使线圈处于稳定压紧状态，以降低噪音。
5、变压器按自冷设计，整体浇注的高(低)压线圈筒壁内部预留有纵向通风道，可配备强迫风冷装置(冷却风机)，采用强迫风冷装置后，可提高输出容量20%。
6、配有温控器，在低压线圈顶部的预埋孔内放置铂电阻(Pt100)。以监测变压器绕组温升，自动启停冷却风机并设有故障报警、超温报警和超温跳闸功能，为干式变压器提供可靠的过载保护装置，从而提高干式变压器运行的安全性。

1. The coil is wound by copper wire or foil, reinforced with glass fiber, epoxy resin without filler vacuum drying, degassing and dehumidification, casting, high mechanical strength, short circuit resistance and strong impact resistance.

2. The first end of the high-voltage winding and the intermediate tapping tap are embedded with copper inserts. The steel is good, easy to shift, beautiful and neat.

3. the iron core is made of high-quality grain oriented cold-rolled silicon steel sheet, 45 degree full oblique multi-step seam. The surface is covered with a resin insulating coating to resist moisture, rust and noise.

4. The elastic core is clamped between the iron core, the clamp and the coil, so that the coil is in a stable compression state to reduce noise.

5. The transformer is designed according to self-cooling. There is a longitudinal air duct inside the high (low) pressure coil wall of the whole casting. It can be equipped with forced air cooling device (cooling fan). After forced air cooling device, the output capacity can be increased. %.

6. With a thermostat, place a platinum resistor (Pt100) in the pre-buried hole at the top of the low voltage coil. In order to monitor the temperature rise of the transformer winding, the cooling fan is automatically started and stopped, and the fault alarm, over-temperature alarm and over-temperature trip function are provided to provide a reliable overload protection device for the dry-type transformer, thereby improving the safety of the dry-type transformer operation.

产品结构 Structure

  铁芯：铁芯选用进口优质冷轧硅钢片，三阶全斜接缝结构，芯柱采用F级无纬带绑扎，铁芯表面采用环氧树脂包封，降低了空载损耗，空载电流和铁皮噪声，夹件和紧回件经特殊表面处理，使产品外观质量有了进一步提高。
   温控系统和风冷系统：采用横流顶吹式冷却风机，该冷却风机具有噪声小，风压高，外形美观等特点，增强了变压器的过载能力。温度控制采用智能温控仪，提高了变压器运行安全可靠性。
保护外壳和出线母排：保护外壳对变压器作进一步安全保护，防护等级有IP20、IP23等。外壳材料有铝合金、冷轧钢板，不锈钢等供用户选择。低压出线用标准母线排出线，侧出线和顶出线均可，也可为用户设计特殊出线方式。

  Iron core: The iron core is made of imported high-quality cold-rolled silicon steel sheet, the third-order full-slant joint structure, the core column is bundled with F-class non-latitude belt, and the iron core surface is sealed with epoxy resin, which reduces the no-load loss and no-load current. And the iron sheet noise, the clip and the back part are specially treated to improve the appearance quality of the product.
Temperature control system and air cooling system: The cross-flow top-blown cooling fan is adopted. The cooling fan has the characteristics of low noise, high wind pressure and beautiful appearance, which enhances the overload capability of the transformer. The temperature control adopts an intelligent temperature controller to improve the safety and reliability of the transformer operation.
Protective casing and outlet busbar: The protective casing provides further protection for the transformer. The protection grades are IP20, IP23 and so on. The outer casing material is aluminum alloy, cold rolled steel plate, stainless steel, etc. for users to choose. The standard busbar discharge line for low-voltage outlets can be used for both side outlets and top outlets. Special outlets can also be designed for users.

产品用料 Materials

材料名称 Component	材质 Material	产地及质量特点 Place of origin and Characteristics

硅钢片 Silicon steel sheet	全新优质晶粒取向高导磁冷轧硅钢片 New high quality grain oriented high permeability magnetic cold rolled silicon steel sheet	产地：武钢或新日铁。激磁电流、铁损耗、饱和参数性能优越。冷轧硅钢带由于具有较高的导磁系数和较低的损耗，因此用来制作变压器具有体积小、重量轻、效率高的优势。热轧硅钢带则逊色于冷轧硅钢带，而二次片、拼接片等对变压器使用寿命危害就更不用说了。 Origin: WISCO or Nippon Steel. Excitation current, iron loss, and saturation parameters are superior. Cold-rolled silicon steel strips have the advantages of small size, light weight and high efficiency due to their high magnetic permeability and low loss. Hot-rolled silicon steel strips are inferior to cold-rolled silicon steel strips, and secondary sheets, splices, etc. are not harmful to the service life of transformers.
变压器绕组 Transformer winding	紫铜 Copper	产地：洛阳铜业。含铜量99.999%，国家规定：电工用铜纯度必须在99.5%以上的紫铜。黄铜可用在小功率非电力变压器上，且属于不合格违规使用。另用黄铜做变压器线圈会增加铜损（负载损耗），降低变压器使用功率等，是十分有害的。 Origin: Luoyang Copper. The copper content is 99.999%, and the state stipulates that the copper purity of the electrician must be 99.5% or more. Brass can be used on low-power non-power transformers and is a non-conforming violation. Another use of brass as a transformer coil will increase copper loss (load loss) and reduce the power used by the transformer. It is very harmful.
母排 Busbar
绝缘油 Insulating oil	环烷基矿物油 Cycloalkyl mineral oil	产地：新疆克拉玛依油田。清洁而透明的液体，不得有沉淀物、机械杂质悬浮物及棉絮状物质。劣质油或二次油存在加速变压器老化，噪音大、易短路烧毁，使用寿命短。 Origin: Xinjiang Karamay Oilfield. Clean and transparent liquids must be free of deposits, suspended solids of mechanical impurities and cotton-like materials. Inferior oil or secondary oil exists to accelerate the aging of the transformer, the noise is large, the short circuit is easy to burn, and the service life is short.
绝缘纸 Insulating paper	牛皮纸/NOMEX 绝缘纸 Kraft paper / NOMEX insulation paper	产地：许昌绝缘材料厂或美国杜邦公司。绝缘纸是变压器的重要组成部分，变压器老化、烧坏的主要原因之一是使用低价劣质绝缘纸，易发生电弧击穿，缩短了使用寿命。 Origin: Xuchang Insulation Material Factory or DuPont Company of the United States. Insulation paper is an important part of the transformer. One of the main reasons for the aging and burning of the transformer is the use of low-cost inferior insulating paper, which is prone to arc breakdown and shortens the service life.
环氧树脂 Epoxy resin	高环氧值(>40)6101环氧树脂 igh epoxy value (>40) 6101 epoxy resin	产地：瑞士汽巴嘉吉。F/H级蕞高耐温155℃/180℃。耐温、耐压、硬度、收缩率、吸水率、玻化温度、粘接强度、拉伸强度等技术指标对干式变压器绝缘、浇注质量非常关键。 Origin: Swiss Ciba Cargill. The F/H grade has a maximum temperature resistance of 155 ° C / 180 ° C. Technical indexes such as temperature resistance, pressure resistance, hardness, shrinkage, water absorption, glass transition temperature, bonding strength and tensile strength are critical to the insulation and casting quality of dry-type transformers.
电工木 Electrician wood	榉树木 Eucalyptus	产地：东南亚、内蒙古，由南方机车厂、内蒙古阿里河电厂提供，绝缘能力强，抗张强度高。 Origin: Southeast Asia, Inner Mongolia, provided by Southern Locomotive Works and Inner Mongolia Alihe Power Plant, with strong insulation and high tensile strength.

执行标准 Standard

1、GB1094.11-2007 干式电力变压器
2、GB/T10228-2008 干式电力变压器技术参数和要求
3、GB1094.10-2003 电力变压器第3部分：绝缘水平、绝缘试验和外绝缘空气间隙
4、JB/T10008-2004 6~500KV级变压器声级
5、JB/T56009-1998 干式电力变压器产品质量分等

1. GB1094.11-2007 dry power transformer

2. GB/T10228-2008 dry power transformer technical parameters and requirements

3. GB1094.10-2003 Power transformers - Part 3: Insulation level, insulation test and external insulation air gap

4. JB/T10008-2004 6~500KV class transformer sound level

5. JB/T56009-1998 dry power transformer product quality grading

技术参数 Parameters

变压器型号 Transformer Type	电压组合 Voltage Combination			联结组别 Connection Group	短路阻抗 Short- circuit Impedance	损耗(W) Loss		空载电流 No-load current （%）	产品报价 Quotation
变压器型号 Transformer Type	高压 HV	分接范围 Tap Range	低压 LV	联结组别 Connection Group	短路阻抗 Short- circuit Impedance	空载 No-load Loss	负载 Load Loss	空载电流 No-load current （%）	产品报价 Quotation
SCB13-30/10-0.4	11 10.5 10 6.3 6	±5% 或 ±2×2.5%	0.4 0.69	Yyn0 或 Dyn11	4%	153	710	2.4	获取产品价格 Get Price
SCB13-50/10-0.4						218	1000	2.4	获取产品价格 Get Price
SCB13-63/10-0.4						279	1220	2.1	获取产品价格 Get Price
SCB13-80/10-0.4						300	1380	1.8	获取产品价格 Get Price
SCB13-100/10-0.4						324	1570	1.8	获取产品价格 Get Price
SCB13-125/10-0.4						380	1850	1.6	获取产品价格 Get Price
SCB13-160/10-0.4						437	2130	1.6	获取产品价格 Get Price
SCB13-200/10-0.4						502	2530	1.4	获取产品价格 Get Price
SCB13-250/10-0.4						583	2760	1.4	获取产品价格 Get Price
SCB13-315/10-0.4						712	3470	1.2	获取产品价格 Get Price
SCB13-400/10-0.4						793	3990	1.2	获取产品价格 Get Price
SCB13-500/10-0.4						940	4880	1.2	获取产品价格 Get Price
SCB13-630/10-0.4					6%	1085	5880	1.0	获取产品价格 Get Price
SCB13-800/10-0.4						1231	6960	1.0	获取产品价格 Get Price
SCB13-1000/10-0.4						1433	8130	1.0	获取产品价格 Get Price
SCB13-1250/10-0.4						1692	9690	1.0	获取产品价格 Get Price
SCB13-1600/10-0.4						1984	11730	1.0	获取产品价格 Get Price
SCB13-2000/10-0.4						2470	14450	0.8	获取产品价格 Get Price
SCB13-2500/10-0.4						2916	17170	0.8	获取产品价格 Get Price
注：以上参数仅供参考，具体以实际为准。我公司不断对产品进行优化设计，如有改动，恕不另行通知，解释权归hjc878黄金城官网所有！ Note: The above parameters are for reference only, which is subject to actual conditions. Our company continuously optimizes the design of the products, and if there are any changes without prior notice, the right of interpretation belongs to Beijing Henganyuan Electrical Equipment Co., Ltd.!

安装尺寸 Size

变压器型号 Transformer Type	外形尺寸(mm) Dimensions	安装轨距(mm) Installation Gauge	重量(Kg) Weight

SCB13-30/10-0.4	645460660	400*400	265
SCB13-50/10-0.4	690460710	400*400	300
SCB13-63/10-0.4	810460790	500*400	395
SCB13-80/10-0.4	830460880	500*400	485
SCB13-100/10-0.4	910800925	550*740	575
SCB13-125/10-0.4	910800955	550*740	620
SCB13-160/10-0.4	9108001000	550*740	650
SCB13-200/10-0.4	9409001090	550*820	900
SCB13-250/10-0.4	9809001160	550*820	1020
SCB13-315/10-0.4	10209001235	550*820	1280
SCB13-400/10-0.4	10309001260	550*820	1450
SCB13-500/10-0.4	11408901315	660*820	1560
SCB13-630/10-0.4	12108901250	660*820	1650
SCB13-800/10-0.4	13508901350	820*820	1970
SCB13-1000/10-0.4	13808901350	820*820	2170
SCB13-1250/10-0.4	14258901430	820*820	2750
SCB13-1600/10-0.4	142011001680	820*1020	3200
SCB13-2000/10-0.4	154012001735	1070*1120	3710
SCB13-2500/10-0.4	155012001905	1070*1120	4460
注：以上参数仅供参考，具体以实际为准。我公司不断对产品进行优化设计，如有改动，恕不另行通知，解释权归hjc878黄金城官网所有！ Note: The above parameters are for reference only, which is subject to actual conditions. Our company continuously optimizes the design of the products, and if there are any changes without prior notice, the right of interpretation belongs to Beijing Henganyuan Electrical Equipment Co., Ltd.!

订货须知 Order

1、产品型号
　　2、额定容量(kVA)，三绕组变压器高、中、低压绕组容量比(％)
　　3、高压额定电压(kV)，调压方式，级数及分接电压百分比(％)
　　4、中压额定电压(kV)，调压方式，级数及分接电压百分比(％)
　　5、低压额定电压(kV)
　　6、短路阻抗(％)
　　7、联结组标号
　　8、冷却方式
　　9、特殊要求：如环境温度、海拔高度、相数、频率、有载分接开关、绝缘水平、环境要求。

1. product model

2.rated capacity (kVA), three-winding transformer high, medium and low voltage winding capacity ratio (%)

3. high voltage rated voltage (kV), voltage regulation mode, number of stages and tap voltage percentage (%)

4.the medium voltage rated voltage (kV), voltage regulation mode, the number of stages and the percentage of tapping voltage (%)

5. low voltage rated voltage (kV)

6.short circuit impedance (%)

7. the junction group label

8. cooling method

9.special requirements: such as ambient temperature, altitude, phase number, frequency, on-load tap-changer, insulation level, environmental requirements.