陕西S13-M型低损耗全密封油浸式变压器-北京澳门皇家堵场电气集团有限公司

陕西S13-M型低损耗全密封油浸式变压器

所属分类：陕西油浸式变压器
点击次数：
发布日期：2019/02/26
规格：
类型：
在线询价

详细介绍

产品概述 Overview

S13-M型全密封油浸式电力变压器继承了S11-M型变压器损耗低、噪声低、效率高的优点，空载损耗降低10%-15%左右，可取得良好的节能效果并减少污染。全密封式变压器与普通油浸式变压器相比，取消了储油柜，油体积的变化由波纹油箱的波纹片的弹性来自动调节补偿，变压器与空气隔绝，防止和减缓油的劣化和绝缘老化，增强运行可靠性，正常运行免维护。

S13-M full-sealed oil-immersed power transformer inherits the advantages of low loss, low noise and high efficiency of S11-M transformer. The no-load loss is reduced by 10%-15%, which can achieve good energy saving effect and reduce pollution. Compared with ordinary oil-immersed transformers, the fully sealed transformers eliminate the oil storage cabinet. The change of oil volume is automatically adjusted and compensated by the elasticity of the corrugated sheet of the corrugated oil tank. The transformer is insulated from the air to prevent and slow down the deterioration of the oil and the insulation aging. , to enhance operational reliability, maintenance-free maintenance.

产品展示 Display

非晶合金变压器

型号含义 Meaning

结构特点 Structure

1、变压器铁芯采用进口优质冷轧硅钢片叠积而成，大大降低空载损耗和空载电流，并对铁芯进行绑扎，保证铁芯的紧实度，降低噪声。
2、高低压绕组用无氧铜绕制，低压绕组500kVA及以下采用双层圆筒式结构。630kVA及以上采用双螺旋或四螺旋结构，高压绕组采用多层圆筒式结构。
3、变压器连接组采用Dyn11,减少谐波对电网的影响，改善供电质量。
4、变压器为全密封结构，延长使用寿命，免吊芯，免维修。
5、实测噪声值低于标准。本系列变压器经正常运输后，不需要吊芯检查，即可安装有关的零部件，进行验收项目试验，合格后即可投入运行。

1. The transformer core is made of imported high-quality cold-rolled silicon steel sheets, which greatly reduces the no-load loss and no-load current, and binds the iron core to ensure the tightness of the iron core and reduce noise.

2. The high and low voltage windings are wound with oxygen-free copper, and the low-voltage windings of 500kVA and below adopt a double-layer cylindrical structure. 630kVA and above adopt double helix or four-helical structure, and high-voltage winding adopts multi-layer cylindrical structure.

3. The transformer connection group adopts Dyn11 to reduce the influence of harmonics on the power grid and improve the power supply quality.

4, the transformer is a fully sealed structure, extending the service life, free of core, maintenance-free.

5. The measured noise value is lower than the standard. After the normal transmission of this series of transformers, the relevant parts and components can be installed without the inspection of the core, and the acceptance project test can be carried out.

产品用料 Materials

材料名称 Component	材质 Material	产地及质量特点 Place of origin and Characteristics

硅钢片 Silicon steel sheet	全新优质晶粒取向高导磁冷轧硅钢片 New high quality grain oriented high permeability magnetic cold rolled silicon steel sheet	产地：武钢或新日铁。激磁电流、铁损耗、饱和参数性能优越。冷轧硅钢带由于具有较高的导磁系数和较低的损耗，因此用来制作变压器具有体积小、重量轻、效率高的优势。热轧硅钢带则逊色于冷轧硅钢带，而二次片、拼接片等对变压器使用寿命危害就更不用说了。 Origin: WISCO or Nippon Steel. Excitation current, iron loss, and saturation parameters are superior. Cold-rolled silicon steel strips have the advantages of small size, light weight and high efficiency due to their high magnetic permeability and low loss. Hot-rolled silicon steel strips are inferior to cold-rolled silicon steel strips, and secondary sheets, splices, etc. are not harmful to the service life of transformers.
变压器绕组 Transformer winding	紫铜 Copper	产地：洛阳铜业。含铜量99.999%，国家规定：电工用铜纯度必须在99.5%以上的紫铜。黄铜可用在小功率非电力变压器上，且属于不合格违规使用。另用黄铜做变压器线圈会增加铜损（负载损耗），降低变压器使用功率等，是十分有害的。 Origin: Luoyang Copper. The copper content is 99.999%, and the state stipulates that the copper purity of the electrician must be 99.5% or more. Brass can be used on low-power non-power transformers and is a non-conforming violation. Another use of brass as a transformer coil will increase copper loss (load loss) and reduce the power used by the transformer. It is very harmful.
母排 Busbar
绝缘油 Insulating oil	环烷基矿物油 Cycloalkyl mineral oil	产地：新疆克拉玛依油田。清洁而透明的液体，不得有沉淀物、机械杂质悬浮物及棉絮状物质。劣质油或二次油存在加速变压器老化，噪音大、易短路烧毁，使用寿命短。 Origin: Xinjiang Karamay Oilfield. Clean and transparent liquids must be free of deposits, suspended solids of mechanical impurities and cotton-like materials. Inferior oil or secondary oil exists to accelerate the aging of the transformer, the noise is large, the short circuit is easy to burn, and the service life is short.
绝缘纸 Insulating paper	牛皮纸/NOMEX 绝缘纸 Kraft paper / NOMEX insulation paper	产地：许昌绝缘材料厂或美国杜邦公司。绝缘纸是变压器的重要组成部分，变压器老化、烧坏的主要原因之一是使用低价劣质绝缘纸，易发生电弧击穿，缩短了使用寿命。 Origin: Xuchang Insulation Material Factory or DuPont Company of the United States. Insulation paper is an important part of the transformer. One of the main reasons for the aging and burning of the transformer is the use of low-cost inferior insulating paper, which is prone to arc breakdown and shortens the service life.
环氧树脂 Epoxy resin	高环氧值(>40)6101环氧树脂 igh epoxy value (>40) 6101 epoxy resin	产地：瑞士汽巴嘉吉。F/H级蕞高耐温155℃/180℃。耐温、耐压、硬度、收缩率、吸水率、玻化温度、粘接强度、拉伸强度等技术指标对干式变压器绝缘、浇注质量非常关键。 Origin: Swiss Ciba Cargill. The F/H grade has a maximum temperature resistance of 155 ° C / 180 ° C. Technical indexes such as temperature resistance, pressure resistance, hardness, shrinkage, water absorption, glass transition temperature, bonding strength and tensile strength are critical to the insulation and casting quality of dry-type transformers.
电工木 Electrician wood	榉树木 Eucalyptus	产地：东南亚、内蒙古，由南方机车厂、内蒙古阿里河电厂提供，绝缘能力强，抗张强度高。 Origin: Southeast Asia, Inner Mongolia, provided by Southern Locomotive Works and Inner Mongolia Alihe Power Plant, with strong insulation and high tensile strength.

执行标准 Standard

1、IEC60076-1:1993 电力变压器
2、GB1094.1-1996 电力变压器
3、GB6451-2008 油浸式电力变压器技术参数和要求
4、JB/T10088-2004 6KV~500KV级电力变压器声级

1. IEC60076-1:1993 Power Transformer

2. GB1094.1-1996 power transformer

3. GB6451-2008 oil immersed power transformer technical parameters and requirements

4. JB/T10088-2004 6KV~500KV class power transformer sound level

使用条件 Conditions

1、蕞高环境温度：+40℃
2、蕞低环境温度：-25℃
3、海拔高度：<1500m
4、蕞高月平均相对湿度：90%（20℃）
5、安装地点：安装在没有火灾、爆炸危险、严重污秽、化学腐蚀及剧烈震动的场所，户内或户外。

1. the highest ambient temperature: +40 ° C

2. the minimum ambient temperature: -25 ° C

3. Altitude: <1500m

4. the highest monthly average relative humidity: 90% (20 ° C)

5. Installation location: Installed in a place without fire, explosion hazard, serious pollution, chemical corrosion and severe vibration, indoors or outdoors.

技术参数 Parameters

变压器型号 Transformer Type	电压组合 Voltage Combination			联结组别 Connection Group	短路阻抗 Short- circuit Impedance	损耗(W) Loss		空载电流 No-load current （%）	产品报价 Quotation
变压器型号 Transformer Type	高压 HV	分接范围 Tap Range	低压 LV	联结组别 Connection Group	短路阻抗 Short- circuit Impedance	空载 No-load Loss	负载 Load Loss	空载电流 No-load current （%）	产品报价 Quotation
S13-M-30/10-0.4	11 10.5 10 6.3 6	±5% 或 ±2×2.5%	0.4 0.69	Yyn0 或 Dyn11	4%	85	630	2.1	获取产品价格 Get Price
S13-M-50/10-0.4						111	910	2.0	获取产品价格 Get Price
S13-M-63/10-0.4						128	1090	1.9	获取产品价格 Get Price
S13-M-80/10-0.4						153	1310	1.8	获取产品价格 Get Price
S13-M-100/10-0.4						170	1580	1.6	获取产品价格 Get Price
S13-M-125/10-0.4						204	1890	1.5	获取产品价格 Get Price
S13-M-160/10-0.4						238	2130	1.4	获取产品价格 Get Price
S13-M-200/10-0.4						289	2730	1.3	获取产品价格 Get Price
S13-M-250/10-0.4						340	3200	1.2	获取产品价格 Get Price
S13-M-315/10-0.4						408	3830	1.1	获取产品价格 Get Price
S13-M-400/10-0.4						485	4520	1.0	获取产品价格 Get Price
S13-M-500/10-0.4						578	5410	1.0	获取产品价格 Get Price
S13-M-630/10-0.4					4.5%	689	6200	0.9	获取产品价格 Get Price
S13-M-800/10-0.4						833	7500	0.8	获取产品价格 Get Price
S13-M-1000/10-0.4						978	10300	0.7	获取产品价格 Get Price
S13-M-1250/10-0.4						1156	12000	0.6	获取产品价格 Get Price
S13-M-1600/10-0.4						1394	14500	0.6	获取产品价格 Get Price
S13-M-2000/10-0.4						1785	17820	0.4	获取产品价格 Get Price
S13-M-2500/10-0.4						2125	20700	0.4	获取产品价格 Get Price
注：以上参数仅供参考，具体以实际为准。我公司不断对产品进行优化设计，如有改动，恕不另行通知，解释权归澳门皇家赌场所有！ Note: The above parameters are for reference only, which is subject to actual conditions. Our company continuously optimizes the design of the products, and if there are any changes without prior notice, the right of interpretation belongs to Beijing Henganyuan Electrical Equipment Co., Ltd.!

安装尺寸 Size

变压器型号 Transformer Type	外形尺寸(mm) Dimensions	安装轨距(mm) Installation Gauge	重量(Kg) Weight

S13-M-30/10-0.4	645460660	400*400	265
S13-M-50/10-0.4	690460710	400*400	300
S13-M-63/10-0.4	810460790	500*400	395
S13-M-80/10-0.4	830460880	500*400	485
S13-M-100/10-0.4	910800925	550*740	575
S13-M-125/10-0.4	910800955	550*740	620
S13-M-160/10-0.4	9108001000	550*740	650
S13-M-200/10-0.4	9409001090	550*820	900
S13-M-250/10-0.4	9809001160	550*820	1020
S13-M-315/10-0.4	10209001235	550*820	1280
S13-M-400/10-0.4	10309001260	550*820	1450
S13-M-500/10-0.4	11408901315	660*820	1560
S13-M-630/10-0.4	12108901250	660*820	1650
S13-M-800/10-0.4	13508901350	820*820	1970
S13-M-1000/10-0.4	13808901350	820*820	2170
S13-M-1250/10-0.4	14258901430	820*820	2750
S13-M-1600/10-0.4	142011001680	820*1020	3200
S13-M-2000/10-0.4	154012001735	1070*1120	3710
S13-M-2500/10-0.4	155012001905	1070*1120	4460
注：以上参数仅供参考，具体以实际为准。我公司不断对产品进行优化设计，如有改动，恕不另行通知，解释权归澳门皇家赌场所有！ Note: The above parameters are for reference only, which is subject to actual conditions. Our company continuously optimizes the design of the products, and if there are any changes without prior notice, the right of interpretation belongs to Beijing Henganyuan Electrical Equipment Co., Ltd.!

订货须知 Order

1、产品型号
　　2、额定容量(kVA)，三绕组变压器高、中、低压绕组容量比(％)
　　3、高压额定电压(kV)，调压方式，级数及分接电压百分比(％)
　　4、中压额定电压(kV)，调压方式，级数及分接电压百分比(％)
　　5、低压额定电压(kV)
　　6、短路阻抗(％)
　　7、联结组标号
　　8、冷却方式
　　9、特殊要求：如环境温度、海拔高度、相数、频率、有载分接开关、绝缘水平、环境要求。

1. product model

2.rated capacity (kVA), three-winding transformer high, medium and low voltage winding capacity ratio (%)

3. high voltage rated voltage (kV), voltage regulation mode, number of stages and tap voltage percentage (%)

4.the medium voltage rated voltage (kV), voltage regulation mode, the number of stages and the percentage of tapping voltage (%)

5. low voltage rated voltage (kV)

6.short circuit impedance (%)

7. the junction group label

8. cooling method

9.special requirements: such as ambient temperature, altitude, phase number, frequency, on-load tap-changer, insulation level, environmental requirements.